Unger
Pro Handle (AT-050)
This
rubber-coated squeegee handle works with many different
squeegee blade attachments: Clear Max, Blue Max, and of
course the regular squeegee blade with the soft rubber
insert (for glass prep) in the stainless steel channels.
Essential tool for glass cleaning and for using the special
higher durometer finishing squeegee blades.
Back
to top
|
18" Squeegee & Channel
(top) (AT-056)
12" Squeegee & Channel (second from top)
(AT-055)
8" Squeegee & Channel (second from bottom)
(AT-054)
6" Squeegee & Channel (at bottom)
(AT-053)
Stainless
steel channel and soft rubber squeegee blade insert for use
with the Unger Pro Handle (AT-050). The 8-18" lengths
ARE ideal for most residential/ commercial window films
installations. Used in the glass cleaning process and in the
final cleanup after the actual film installation to remove
soap streaks or smudges. The 6" length channel can be
used for automotive use.
Back
to top
|
18"
Squeegee Blade (AT-0018)
12"
Squeegee Blade (AT-0012)
8"
Squeegee Blade (AT-0008)
6"
Squeegee Blade (AT-0006)
Differing
lengths of rubber blade for Pro Unger squeegee channel
(AT-050), used
for window cleaning, not installation.
Back
to top
|
6" Pro Squeegee Deluxe
(AT-062)
A
"finishing" (installation) squeegee as a
ready-to-use assembly. Used to remove application solution
from beneath the film during the installation of all film
types. Recommended for safety/security films, 4 mil and
thicker.
Back
to top
|
8" Pro Squeegee Deluxe
(AT-064)
A
"finishing" (installation) squeegee as a
ready-to-use assembly. Used to remove application solution
from beneath the film during the installation of all film
types.
Back
to top
|
6" Pro Squeegee Blade
(AT-063)
8" Pro Squeegee Blade
(AT-061)
Replacement
blade to the 6" AND 8"Pro Squeegee (AT-062)
used as a means of removing application solutions from
beneath the film during the installation of all film
types.
Back
to top
|
6" Flatfoot Squeegee Blade
(AT-069)
8" Flatfoot Squeegee Blade
(AT-059)
Flatfoots
are specially angled blades for the Pro Squeegee. The
angle is designed to maximize the surface area in contact
with the film, thereby removing much more mounting
solution than a standard Pro blade with a square edge.
These are special order items, please call for availability.
Back
to top
|
GT042
- 8" Silver Security Squeegee (AT-042)
Comfortable, ergonomic
handle is designed especially for security film
installation. Advance curved handle applies more pressure
to surface, reducing fatigue and ensuring easier, better
installations. Blade is replaceable with either the
Flatfoot (AT-059) or Pro Squeegee (AT-061) blade.
Back
to top
|
Motus D-Grip Handle
(AT-030)
Increase
the leverage of a standard handled squeegee by adding a
D-Grip Motus handle. Excellent for heavy, security film
applications.
Back
to top
|
28" Tube Squeegee
(AT-121)
Squeegee
tool used for glass cleaning. Not recommended for
installation of films. Sometimes called the
"Smoothie."
Back
to top
|
28" Smoothie Blade
(AT-146)
Replacement
blade squeegee tool used for glass cleaning. Economy
size usually cut to shorter 4-5" lengths before use.
Not recommended for installation of films.
Back
to top
|
18.5" Yellow Blade
(AT-147)
Economy
size squeegee usually cut to shorter 4-5" lengths
before use. Used for removal of application solution during
the installation process. (Handle sold separately.)
Back
to top
|
|
Red Devil Squeegee
(AT-033)
Angled, high durometer squeegee.
Excellent for corners.
Back
to top
|
Slim Foot Squeegee
(AT-040)
Modeled after the Big Foot Squeegee,
the slim foot has a slender design that can reach into tighter
openings. The no rib squeegee helps reach behind break lights and
has a vinyl grip for secure handling.
Back
to top
|
Blue Max 5" Hand Squeegee
(AT-117)
Excellent
as finishing a squeegee in automotive and flat-glass
applications, especially for sputtered films. Harder than
AT-203, this tool is superior for water evacuation on films
requiring maximum water removal, though not as effective on
severely compound curved glass because of its greater
rigidity. For automotive applications, many installers
therefore prefer the Clear Max squeegee, especially on
curved glass. Installers generally cut off left & right
sides at an angle to allow leading edge to better squeegee
into corners (see AT-122, AT-204).
Back
to top
|
Super Clear Max Squeegee
(AT-203)
Excellent
as finishing squeegee tool; high durometer, yet flexible.
For mounting inside in the Unger Pro handle. More flexible
than the AT-117 Blue Max auto squeegee. Has beveled leading
edge for excellent flush mounting. Installers generally cut
off left & right sides at an angle to allow leading edge
to better squeegee into corners. (Handle sold separately).
Back
to top
|
6"
Block Squeegee
(AT-148)
12"
Block Squeegee (AT-149)
Combination
squeegee/hard card used as a finishing tool during film
installation. Hard edge, when wrapped in a layer of cotton
fabric or lint-free paper towel, can be used for wicking
water out along borders (after an installation). Can be
cut to various angle shapes to reach tight, sharp cornered
glass areas. Hard-edge sharpness can be maintained by
using AT-068 Hard Card Sharpener.
Back
to top
|
Teflon Edge Squeegee
(AT-086)
While
not actually made of Teflon, this tool is often called the
Teflon "hard-card" or "edge tool." It
is an essential tool for every installer in every
installation situation. When wrapped in a layer of cotton
fabric or lint-free paper towel, it is used for a)
cleaning into corners and along edge gaskets (during glass
preparation), b) wicking water out along borders (after an
installation). Moreover, it can be used for c) direct
squeegeeing of film along borders without any wrapping,
and d) edge trimming by using it as a blade-guide,
creating a uniform tiny gap between the film edge and the
perimeter gasket or frame. Finally, e) it's used to
retract gaskets to slip underneath. It is extremely hard,
yet (if clean) will not scratch SR-coated film. Edge
sharpness can be maintained by using AT-068 Hard Card
Sharpener. Installers often cut down the tool beginning at
the middle top in a straight line to the lower right
corner. This angularity allows the tool to penetrate into
corners for cleaning and squeegeeing purposes.
Back
to top
|
4" Universal Squeegee
(AT-099)
Combination squeegee/hard card used as a
finishing tool during film installation. When wrapped in a
layer of cotton fabric or lint-free paper towel it can be
used for wicking water out along borders (after an
installation) or used for sweeping film flush to the glass
during heat forming procedures. Edge sharpness can be
maintained by using AT-068 Hard Card Sharpener.
Back
to top
|
Diamond Tip
(AT-113)
The
new Diamond Tip Squeegee has several advantages. As
well as the rounded tip, it has a pointed tip for
better ability to reach into small window corners.
Also, the raised edges in the body of the squeegee
make it easier to grip and less likely to slip out of
your hand when it's wet.
Back
to top
|
The
Shuttle
(AT-092)
About
10" (25 cm) long. A hard card able to reach into
tight areas located at the bottom edge of rear window
glass. Edge sharpness can be maintained by using AT-068
Hard Card Sharpener. Name derives for the profile similar
to the Space Shuttle.
Back
to top
|
The
Slammer
(AT-091)
Used
as a hard card-finishing tool for a variety of installation
challenges. When wrapped in a layer of cotton fabric or
lint-free paper towel, it is used for a) cleaning into
corners and along edge gaskets (during glass preparation),
b) wicking water out along borders (after an installation),
and c) direct squeegeeing of film along borders
without any wrapping. Moreover, it can be used for d) easily
reaching the lower portion of rear window glass, e)
temporarily pulling back rub rails or, f) to reach into
sharp angled corners. It is extremely hard, yet (if clean)
will not scratch film. This new and improved design has a
stronger handle, allowing you to apply more pressure onto
the surface. Edge sharpness can be maintained by using
AT-068
Hard Card Sharpener.
Back
to top
|
The Conqueror Squeegee
(AT-202)
Combination
squeegee/hard card used as a finishing tool during film
installation. Able to reach into sharp angled corners. Hard
edge sharpness can be maintained by using AT-068 Hard Card
Sharpener. Can use the hard plastic corner (upper right of
photo) for direct film squeegeeing (with SR films) in tight
corners and, wrapped in a diaper or paper towel, cleaning in
these tight, difficult to reach areas.
Back
to top
|
Lil' Chizler - Blank
(AT-083)
A
much harder tool than the Teflon edge tool, this plastic
device is used for the occasional "press-down"
of small film creases, or scraping away old film remnants
on scratch-sensitive surfaces. Its sharpness allows one to
get under border gaskets, and press down stubborn
"fingers." Caution must be exercised because of
the possibility of scratching film.
Back
to top
|
Clear Super Squeegee - Large
(AT-066)
Combination
squeegee/hard card used as a finishing tool during film
installation. When wrapped in a layer of cotton fabric or
lint-free paper towel it can be used for wicking water out
along borders (during glass cleaning or after an
installation). Edge sharpness can be maintained by using the
Hard Card Sharpener (AT-068). Hard but flexible & about
6 inches wide, has great "scooping" action for
direct "contour" squeegeeing of film in lower
corners of rear windows.
Back
to top
|
Clear Super Squeegee - Small
(AT-067)
Combination
squeegee/hard card used as a finishing tool during film
installation. When wrapped in a layer of cotton fabric or
lint-free paper towel it can be used for wicking water out
along borders (during glass cleaning or after an
installation). Edge sharpness can be maintained by using
the Hard Card Sharpener (AT-068).
Back
to top
|
Hard Card Sharpener
(AT-068)
This
sharpening tool is essential for maintaining the sharpest,
smoothest possible edge on any thin, "hard edge"
tool. Saves money by extending the life of these tools by
more than a hundred-fold. Has replaceable blade: just use
a few segments a stainless steel Ofla blade, remove and
replace with screw driver underneath. An amazing tool
which works like a wood plane.
Back
to top
|
Little Foot Squeegee (AT-046)
This squeegee measures about 6" along
the usable edge. The pointed edge of this tool allows the installer
to squeegee in very tight areas. The little foot has plenty of room
to keep a good grip on the squeegee.
Back
to top
|
Side Swiper Squeegee (AT-207)
Side Swiper Replacement Blade
(AT-118-6)
Reaching the sides and bottom edges of
rear windows and behind speakers has never been easier with this
handled squeegee. Although this squeegee was designed for automotive
use, it has been discovered that it helps to get to the hard to
reach areas on residential applications as well.
Back
to top
|
|
|
6" White Teflon Squeegee (AT-086-6WHT)
A 6" version of your old favorite. This
white firm Teflon hard card is just like the original but with
extended width for greater coverage. It is extra slender for a deep
reach.
Back
to top
|
6" Black Teflon Squeegee (AT-086-6B)
A
6" version of your old favorite. This black semi-firm Teflon hard
card is just like the original but with extended width for greater
coverage. It is extra slender for a deep reach.
Back
to top
|
|
|
Contour Squeegee (Soft) (AT-201GRN)
This tool automatically spreads out
finger tension which makes it the premier applicator for non-flat
surfaces. Perfect for automotive and paint protection installations.
Back
to top
|
Contour Squeegee (Firm) (AT-201YLW)
This
tool automatically spreads out finger tension which makes it the
premier applicator for non-flat surfaces. Perfect for automotive and
paint protection installations.
Back
to top
|
EZ Reach Squeegee (AT-200)
The
first of it's kind corner reach tool! Made extra slender profile for
deep reach ease.
Back
to top
|
The Bulldozer I (Auto) (AT-205)
This design allows you to get those
hard to reach areas, such as behind speakers, brake lights, low
angles and rear windows. This tool has a 6" squeegee blade and is
15" in overall length.
Back
to top
|
The Bulldozer II (Flat) (AT-206)
Like
its brother, this squeegee allows you to reach those tough areas and
has reinforced ribs on the back side for extra rigidity and
leverage. This tool has a 6" squeegee blade and is 15" in overall
length. A great finishing tool.
Back
to top
|
The Scrubber (AT-209)
A must have tool for automotive. This
tool allows you to reach behind speakers and brake lights. Scrub
away adhesive along the bottom edges of sloped rear windows. Uses
replaceable standard white scrub pads cut 2"x3". This tool is 3"x15"
long
Back
to top
|
|
|
|
|
